SpeedyBee F7 V3 Flight Controller

Description

The SpeedyBee F7 V3 Flight Controller (FC ONLY) offers unparalleled performance with up to 8 motor outputs and a lightning-fast 33% faster wireless connection. Equipped with a massive 500MB of onboard flash memory, it supports Betaflight, INAV, or Emuflight, ensuring flexibility for any drone build.

Specifications:

• Product Name: SpeedyBee F7 V3 Flight Controller

• MCU: STM32F722

• IMU (Gyro): BMI270

• USB Port Type: Type-C

• Barometer: BMP280

• OSD Chip: AT7456E chip

• BLE Bluetooth: Supported; used for FC configuration with built-in 2.4 GHz Wi-Fi/Bluetooth combo chip

• Flash FC Firmware Wirelessly: Supported (MENU > FC Firmware Flasher)

• Download/Analyze Blackbox: Supported (MENU > Blackbox Analyzer)

• DJI Air Unit Connection Way: 6-pin connector or direct soldering

• 6-pin DJI Air Unit Plug: Supported; fully compatible with DJI O3, RunCam Link, Caddx Vista, DJI Air Unit V1 (no wire changes needed)

• Flash (for BlackBox): 500MB

• BetaFlight Camera Control Pad: Yes (CC pad on front side)

• Power Input: 3S–6S LiPo

• 5V Output: 10 groups total — 3x +5V pads and 1x BZ+ pad on front side, 6x +5V outputs via bottom connectors (2A total current)

• 9V Output: 2 groups — 1x +9V pad on front side, 1x via bottom connector (4A total current)

• 3.3V Output: Supported; up to 500mA (for 3.3V-input receivers)

• 4.5V Output: Supported; up to 1A (for receiver/GPS even on USB power)

• ESC Signal Pads: M1–M4 (bottom side), M5–M8 (front side)

• UART: 5 sets (UART1, UART2, UART3, UART4 for ESC Telemetry, UART6)

• ESC Telemetry UART: UART4 (R4)

• I2C: Supported (SDA & SCL pads on front side for magnetometer, sonar, etc.)

• LED Pad: Supports WS2812 LEDs via Betaflight firmware

• Buzzer: BZ+ and BZ– pads (5V buzzer support)

• BOOT Button:

  • [A] Hold BOOT + power on = DFU mode (for recovery/firmware flash)

  • [B] While powered:

    • Short press = cycle LED mode

    • Long press = switch SpeedyBee-LED ↔ BF-LED mode

• RSSI Input: Supported (RS pad on front side)

• SmartPort: Supported

• Supported FC Firmware: BetaFlight (default), INAV

• Firmware Target Name: SPEEDYBEEF7V3

• Mounting: 30.5 x 30.5mm (4mm hole diameter)

• Dimensions: 41(L) x 38(W) x 8.1(H) mm

• Weight: 10.7g

Package Includes:

• 1 x SpeedyBee F7 V3 Flight Controller
• 1 x DJI 6pin Cable (80mm)
• 1 x SH 1.0mm 25mm-length 8pin Cable (for FC–ESC connection)
• 1 x M3*8mm Silicone Grommets (for FC)
• 1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (30mm)
• 1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (60mm)
• 1 x 4pin SH1.0 to 4pin JST1.25 FPV Cam Cable (60mm)
• 1 x 4pin SH1.0 Radio Receiver Cable (100mm)
• 1 x 4pin SH1.0 to 4pin SH1.0 Analog VTX Cable
• 1 x 6pin SH1.0 GPS Module Cable without Connector on another end (100mm)
• 1 x 6pin SH1.0 GPS Module Cable Connector for another end