SpeedyBee F405 V4 BLS 60A 30×30 Stack - main

SpeedyBee F405 V4 BLS 60A 30×30 Stack - Image 2

SpeedyBee F405 V4 BLS 60A 30×30 Stack

Name: SpeedyBee F405 V4 BLS 60A 30×30 Stack
SKU: 69226
Availability: OutOfStock
Rating: 4.89 (9 reviews)

by Speedybee

4.89 out of 5

(9 customer reviews)

The SpeedyBee F405 Stack – F405 V4 FC + 60A 3-6s BLHeli_S 4-in-1 ESC – 30×30 features Bluetooth Pairing, Onboard 4-level Battery Indicators, 1000uF Filtering Capacitator, Built-in Barometer, and much more!

$139.99

Out of stock

Categories: 30mm x 30mm, FC / ESC Stacks

Description

From April 2024 now with 60A ESC!

The SpeedyBee F405 Stack – F405 V4 FC + 60A 3-6s BLHeli_S 4-in-1 ESC – 30×30 features Bluetooth Pairing & Configuration, Onboard 4-level Battery Indicators, 1000uF Filtering Capacitator, Built-in Barometer, to name a few. It also offers 4x UARTS, 5V 3A &9V 3A individual BECs, Wireless Motor-direction Changing, 4x LED Strips Soldering Pads, felxible blackbox sd card, and 8 Motors Support.

Specifications

F405 V4 FC

Product Name SpeedyBee F405 V4 30×30 Flight Controller
MCU STM32F405
IMU(Gyro) ICM42688P
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFI Not supported
DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB,
Current Sensor Input Supported. For SpeedyBee BLS 60A ESC, please set scale = 400 and Offset = 0.
Power Input 3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.
9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for receiver and GPS module evenwhen the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 – M4 on bottom side and M5-M8 on front side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry UART R5(UART5)I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V BuzzerBOOT Button Supported.
RSSI Input Supported. Named as RS on the front side.
Smart Port / F.Port Not supported
Supported Flight Controller Firmware BetaFlight(Default), INAV
Firmware Target Name SPEEDYBEEF405V4
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
Weight 10.5g